• Positive opening safety contacts (IEC 60947-5-1) (not dependent upon springs)
• Mechanically-coded actuators utilize two independent operating elements to minimize intentional tampering or defeat
• Rotating head allows actuator engagement from front or back or either of two top positions
• Choice of four standard actuators; special high extraction force actuator is available as option
• NEMA 4, IEC IP65 switch housing rating may be increased to NEMA 4X, IEC IP67 with addition of screw to wiring chamber door
• Insulated device (IEC 60947-5-1) on all models with plastic housings

• Positive opening safety contacts (IEC 60947-5-1); not dependent upon springs)
• Insulated device (IEC 60947-5-1) on all models with plastic housings
• Protective Earth Terminal (IEC 60947-1) on all models with metal housings
• Models which have a separate actuator are keyed to discourage intentional tampering or defeat
• Industry standard limit switch housings: 100, 83, 40, and low-profile 31 millimeter styles are available (EN 50041, EN 50047)
• Models available with rotating actuators for hinged door applications
• Some models feature rotating actuator head

• Model series SI-LS42 (left) and SI-QM100 (right)
• Positive opening safety contacts (IEC 60947-5-1); not dependent upon springs)
• Insulated device (IEC 60947-5-1) on all models with plastic housings
• Protective Earth Terminal (IEC 60947-1) on all models with metal housings
• Choice of two locking mechanism types
• Wide range of solenoid voltages available

• Non-contact safety interlock switches are the best choice for washdown applications; the switch components are sealed and rated NEMA 4X, IEC IP67
• Tolerant of dirt buildup, sensing distance, and alignment
• System consists of three components:
  • Coded magnet
  • Reed switch sensor
  • Controller module
• Magnet contains several differently-polarized magnets, and sensor contains pole-stable reed contacts to minimize possibility of defeat
• Easy installation; can be concealed for added defeat resistance
• Sensor reed switches provide diverse input to the controller module
• Must be used with Gate Monitoring modules for safety applications:

• Monitor one or two mechanical safety switches for a contact failure or wiring fault
• Two redundant output switching channels for connection to control-reliable power interrupt circuits
• Auto reset or monitored manual reset
• Designed to meet standards UL991, EN1088, and EN954-1 (Safety Category 2 or 4)
• 6 amp safety output contacts
• Plug-in terminal blocks
• See Safety Interlock section for both mechanical and magnetic switch selection

• Monitors one magnetic safety switch for a contact failure or wiring fault
• One redundant switching channel
• Auto reset
• 8 amp safety output contacts
• Fixed terminal blocks
• See Safety Interlock section for both mechanical and magnetic switch selection

• Safety switch is integrated and encapsulated into a load-bearing hinge, providing a high degree of protection from intentional defeat
• Switch components concealed inside the hinge are protected from mechanical impact, providing superior performance to actuator-activated safety switches
• Hinge operates to a full 180° range of motion; safety switching point (guard-closed position) is adjustable over the full 0-180° operating range
• When properly interfaced or used with an appropriate controller, two SI-HG80DQD(R) switches can achieve safety category 4, per ISO 13949 (EN 954-1)
• Robust zinc die-cast housing is corrosion resistant

• Simultaneous action of both hand controls generates an output signal; if either hand is released, the output signal from the DUO-TOUCH is cancelled and cannot be reestablished until both hand controls have been released, and simultaneously actuated again
• Redundant forced-guide (positive guided) output contacts are monitored to prevent an output signal from occurring if a fault is detected
• AT-FM-10K, AT-GM/HM-13A and AT-GM/HM-11KM designed to meet Type IIIC requirements of EN574; may be used with STB Series self-checking optical touch buttons
• AT-FM-2A designed to meet Type IIIB/IIIA requirements of EN574; may be used with OTB Series optical touch buttons (available together as a "kit")
• Available in a variety of voltages

Download

• Interface Modules provide isolated safety output contacts for a Primary Safety Device (for example, an optical safety system or safety control module) which has solid-state or relay contact outputs and external device monitoring (EDM) capability.
• Model IM-T-9A features three normally open 6 amp redundant-output channels.
• Model IM-T-11A features two normally open redundant-output channels and one complementary (parallel) normally closed non-safety auxiliary output channel, all rated at 6 amps.
• Independent normally closed outputs for connection to the Primary Safety Device’s monitoring input.
• 24V dc operation
• 22.5 mm (0.9") DIN-rail-mountable housing
• Convenient plug-in terminal blocks

• Contactors provide an additional 10 or 16 amp current carrying capability to any safety system
• Auxiliary contacts provide 3 or 4 additional contacts
• Suppressors extend the life of the actuating device (light screen, two-hand control module, etc.)
• Modular construction for ease of assembly and installation
• Can be used with Banner's optical safety systems, two-hand control modules and emergency-stop safety modules
• Safety Systems with Output Signal Switching Device (OSSD) will use 24V dc Positively Guided Contactors, all other safety systems can use 24V dc or 120V ac Positively Guided Contactors (depending on application)