Contrex-Accessories

Quadrature Sensors

Quadrature Sensor Ring Kits
The advanced Quadrature Sensor Kit that gives you both speed and direction. Accurately.

Quadrature design measures both motor shaft speed and direction.
Pre-gapped and adjusted at CONTREX. No phase or mechanical adjustment is required.
Simply attach to your motor, hook up the wiring, and go. Very easy installation.
Eliminates the need for special brackets and couplers.
Unique design of sensor insert (not cylindrical, like others) creates a fixed sensor gap, providing more accurate readings.
Square-cut design of gear teeth provides a greater measure of accuracy than rounded spur gears.
Provides 60 pulses per revolution. So each gear tooth is 6º resolution of the total pulse rotation.
Teamed up with an intelligent controller (CONTREX CX-1010, or other smart receivers) can interpret 240 edges or 1.5º resolution.
Sizes range from 56C to 254TC and 71D Metric.
Complete Quadrature Sensor Kit includes: flange ring, sensor, 60 tooth gear, junction box, electrical caps, wiring, bolts.
SENSOR TYPE: Quadrature, Bidirectional Shaft Speed Sensor
PULSES PER REVOLUTION: 60 cycles each channel (240 edges)
SENSING SPEED RANGE: Zero speed to 10,000 RPM (shaft speed)
GAP ADJUSTMENT: None required
OPERATING TEMPERATURE: 0º to 70º C
SUPPLY VOLTAGE: +5 to +15 VDC or +15 to 24 VDC
SUPPLY CURRENT: 30 mA @ +5 VDC;   70 mA @ +15 VDC
SWITCHING FREQUENCY LIMIT: 100 kHz
OUTPUT DRIVE TYPES: Differential, Open Collector, Open Collector with pull-up
OUTPUT DRIVE CAPABILITY: 250 mA per channel continuous
MAXIMUM LOAD: 70 ohms per channel @ +15 VDC

Literature
Ring Specifications 56C and 143TC (PDF format, 437kb)
Ring Specifications 182TC, 213TC and 245TC (PDF format, 447kb)
Ring Specifications 71D (PDF format, 432kb)

Quadrature Sensor Ring Kits - 60 Tooth Gear - 5 to 15 VDC - Open Collector
7300-1310     56C, 5/8" Bore, with Pull-up Resistor
7300-1311     143TC, 7/8" Bore, with Pull-up Resistor
7300-1312     182TC, 1-1/8" Bore, with Pull-up Resistor
7300-1313     213TC, 1-3/8" Bore, with Pull-up Resistor
7300-1314     254TC, 1-5/8" Bore, with Pull-up Resistor
7300-1355     71D Metric, 14mm Bore, with Pull-up Resistor
7300-1315     56C, 5/8" Bore, without Pull-up Resistor
7300-1316     143TC, 7/8" Bore, without Pull-up Resistor
7300-1317     182TC, 1-1/8" Bore, without Pull-up Resistor
7300-1318     213TC, 1-3/8" Bore, without Pull-up Resistor
7300-1319     254TC, 1-5/8" Bore, without Pull-up Resistor
7300-1357     71D Metric, 14mm Bore, without Pull-up Resistor

Quadrature Sensor Ring Kits - 60 Tooth Gear - 5 to 15 VDC - Differential
7300-1370     56C, 5/8" Bore, Line Driver Output
7300-1371     143TC, 7/8" Bore, Line Driver Output
7300-1372     182TC, 1-1/8" Bore, Line Driver Output
7300-1373     213TC, 1-3/8" Bore, Line Driver Output
7300-1374     254TC, 1-5/8" Bore, Line Driver Output
7300-1375     71D Metric, 14mm Bore, Line Driver Output

Quadrature Sensor Ring Kits - 60 Tooth Gear - 15 to 24 VDC - Open Collector
7300-1410     56C, 5/8" Bore, with Pull-up Resistor
7300-1411     143TC, 7/8" Bore, with Pull-up Resistor
7300-1412     182TC, 1-1/8" Bore, with Pull-up Resistor
7300-1413     213TC, 1-3/8" Bore, with Pull-up Resistor
7300-1414     254TC, 1-5/8" Bore, with Pull-up Resistor
7300-1415     71D Metric, 14mm Bore, with Pull-up Resistor
7300-1420     56C, 5/8" Bore, without Pull-up Resistor
7300-1421     143TC, 7/8" Bore, without Pull-up Resistor
7300-1422     182TC, 1-1/8" Bore, without Pull-up Resistor
7300-1423     213TC, 1-3/8" Bore, without Pull-up Resistor
7300-1424     254TC, 1-5/8" Bore, with out Pull-up Resistor
7300-1425     71D Metric, 14mm Bore, without Pull-up Resistor

Single Channel Sensors

Single Channel Sensor Ring Kits
The advanced Single Channel Sensor Kit that gives you speed. Accurately.

Single Channel design measures motor shaft speed.
Pre-gapped and adjusted at CONTREX. No phase or mechanical adjustment is required.
Simply attach to your motor, hook up the wiring, and go. Very easy installation.
Eliminates the need for special brackets and couplers.
Unique design of sensor insert (not cylindrical, like others) creates a fixed sensor gap, providing more accurate readings.
Square-cut design of gear teeth provides a greater measure of accuracy than rounded spur gears.
Provides 60 pulses per revolution. So each gear tooth is 6º resolution of the total pulse rotation.
Teamed up with an intelligent controller (CONTREX CX-1010, or other smart receivers) can interpret 120 edges or 3º resolution.
Sizes range from 56C to 254TC and 71D Metric.
Complete Single Channel Sensor Kit includes: flange ring, sensor, 60 tooth gear, junction box, electrical caps, wiring, bolts.
SENSOR TYPE: Hall Effect Speed Sensor
PULSES PER REVOLUTION: 60 cycles each channel
SENSING SPEED RANGE: Zero speed to 10,000 RPM (shaft speed)
GAP ADJUSTMENT: None required
OPERATING TEMPERATURE: 0º to 70º C
SUPPLY VOLTAGE: +5 to +15 VDC or +15 to +24 VDC
SUPPLY CURRENT: 20 mA @ +5 VDC;   40 mA @ +15 VDC
SWITCHING FREQUENCY LIMIT: 100 kHz
OUTPUT DRIVE TYPES: Differential, Open Collector, Open Collector with pull-up
OUTPUT DRIVE CAPABILITY: 250 mA per channel continuous
MAXIMUM LOAD: 70 ohms per channel @ +15 VDC

Literature
Ring Specifications 56C and 143TC (PDF format, 437kb)
Ring Specifications 182TC, 213TC and 245TC (PDF format, 447kb)
Ring Specifications 71D (PDF format, 432kb)

Single Channel Sensor Ring Kits - 60 Tooth Gear - 5 to 15 VDC - Open Collector
7300-1430     56C, 5/8" Bore, with Pull-up Resistor
7300-1431     143TC, 7/8" Bore, with Pull-up Resistor
7300-1432     182TC, 1-1/8" Bore, with Pull-up Resistor
7300-1433     213TC, 1-3/8" Bore, with Pull-up Resistor
7300-1434     254TC, 1-5/8" Bore, with Pull-up Resistor
7300-1435     71D Metric, 14mm Bore, with Pull-up Resistor
7300-1440     56C, 5/8" Bore, without Pull-up Resistor
7300-1441     143TC, 7/8" Bore, without Pull-up Resistor
7300-1442     182TC, 1-1/8" Bore, without Pull-up Resistor
7300-1443     213TC, 1-3/8" Bore, without Pull-up Resistor
7300-1444     254TC, 1-5/8" Bore, without Pull-up Resistor
7300-1445     71D Metric, 14mm Bore, without Pull-up Resistor

Single Channel Sensor Ring Kits - 60 Tooth Gear - 5 to 15 VDC - Differential
7300-1450     56C, 5/8" Bore, Line Driver Output
7300-1451     143TC, 7/8" Bore, Line Driver Output
7300-1452     182TC, 1-1/8" Bore, Line Driver Output
7300-1453     213TC, 1-3/8" Bore, Line Driver Output
7300-1454     254TC, 1-5/8" Bore, Line Driver Output
7300-1455     71D Metric, 14mm Bore, Line Driver Output

Single Channel Sensor Ring Kits - 60 Tooth Gear - 15 to 24 VDC - Open Collector
7300-1460     56C, 5/8" Bore, with Pull-up Resistor
7300-1461     143TC, 7/8" Bore, with Pull-up Resistor
7300-1462     182TC, 1-1/8" Bore, with Pull-up Resistor
7300-1463     213TC, 1-3/8" Bore, with Pull-up Resistor
7300-1464     254TC, 1-5/8" Bore, with Pull-up Resistor
7300-1465     71D Metric, 14mm Bore, with Pull-up Resistor
7300-1470     56C, 5/8" Bore, without Pull-up Resistor
7300-1471     143TC, 7/8" Bore, without Pull-up Resistor
7300-1472     182TC, 1-1/8" Bore, without Pull-up Resistor
7300-1473     213TC, 1-3/8" Bore, without Pull-up Resistor
7300-1474     254TC, 1-5/8" Bore, without Pull-up Resistor
7300-1475     71D Metric, 14mm Bore, without Pull-up Resistor

Mag Pick-Up Sensors

Magnetic Pick-Up Ring Kits
The Magnetic Pick-Up Kit that gives you speed.

Magnetic Pick-Up design measures motor shaft speed.
Simply attach to your motor, gap, hook up the wiring, and go. Very easy installation.
Eliminates the need for special brackets and couplers.
Provides 30 or 60 pulses per revolution.
Sizes range from 56C to 254TC.
Complete Magnetic Pick-Up Kit includes: flange ring, sensor, 30 or 60 tooth gear, junction box, electrical caps, wiring, bolts.
SENSOR TYPE: Variable Reluctance Magnetic Speed Sensor
PULSES PER REVOLUTION: 60 PPR
GAP ADJUSTMENT: .005 ± .003 Inch
OPERATING TEMPERATURE: -40º to 105º C
OUTPUT: 15 to 26 Volts Peak-to-Peak at 1000 in/sec with 30 tooth gear and 100k ohms load
RESISTANCE: 100 ohms ± 20%
INDUCTANCE: 6 to 14 mH

Magnetic Pick-Up Ring Kits - 60 Tooth Gear
7300-0980     56C, 5/8" Bore
7300-0982     143TC, 7/8" Bore
7300-0934     182TC, 1-1/8" Bore
7300-0936     213TC, 1-3/8" Bore
7300-0987     254TC, 1-5/8" Bore

Magnetic Pick-Up Ring Kits - 30 Tooth Gear
7300-0981     56C, 5/8" Bore
7300-0983     143TC, 7/8" Bore
7300-0984     182TC, 1-1/8" Bore
7300-0985     213TC, 1-3/8" Bore

ContrexHost 3
for Windows® 98/NT/2000/Me/XP NEW

The ContrexHost Suite of Windows® application programs is available to assist you with the setup and operation of your CONTREX motion control products. ContrexHost 3 supports the full line of CONTREX M-Series, ML-Series, MLP-Series, MB-Series and CX-Series products. New and enhanced features make this latest version of ContrexHost more versatile yet easier to use.

Universal Applications

Network Builder is used to configure ContrexHost with the CONTREX control products connected to your RS485/422 serial communications network. The new Auto Configure features queries your network to identify product models and software revisions.

Control Monitor is the primary ContrexHost module used to setup your CONTREX control products to meet your application requirements and monitor system performance. Select from numerous predefined parameter windows or create your own custom window.

Parameter File Editor is available to create and save product parameter files. Default and downloaded files can be modified as required to meet your installation requirements. Backup your programmed controls using the file save feature.

CX-Series Applications

PLC Programmer provides an alternative method of programming the embedded PLC controller in the CX-Series products. Both the active and default versions of the PLC program can be retrieved for modification.

Custom Units Editor allows you to enter and activate the custom engineering units used to describe the primary display parameter on the Status Screen.

Utilities

Database Editor is available to assist with the maintenance of the CONTREX control product parameter database. Custom software versions of CONTREX control products can be made compliant with ContrexHost through simple database modifications.

Serial Link Debugger can assist you with troubleshooting problems with your RS485/422 serial communications link. This software utility allows for the entry and monitoring of character records transmitted on your serial link.