|
CX-1010
Precision Speed, Ratio and PLC Control The CX-1010 control provides precision speed control with ultimate flexibility to standalone or multi-motor control applications. Using advanced digital feedback techniques, the CX-1010 contains embedded precision control algorithms for Master, Follower, Offset, Inverse and user configurable custom modes of operation. Scaling algorithms permit control parameters to be entered and monitored in engineering units specific to your application. The integrated PLC provides for ultimate flexibility in I/O and sequence control. Eight configuration blocks allow dynamic reconfiguration of user specified parameters via digital input or PLC activation. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed... no code to write. Menu Driven Operator Interface for Setup & Monitoring. Integrated PLC Control. Master, Follower, Offset, Inverse and Custom Scaling. On-the Fly Reconfiguration Parameter Blocks. Fully Isolated Analog and Digital I/O. Optional Analog I/O Card. Optional DeviceNet® Network Card. The CX-1010 control is housed in a ½ DIN vertical instrument enclosure with embedded LCD multi-line operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters through a menu driven screen format. Individual application requirements are met by simply accessing the relevant screen and code parameter, and then entering the appropriate numerical value. Because the CX-1010 control is pre-programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The CX-1010 control has a serial port for RS485 communication. ContrexHost software, when installed on a Windows PC or laptop, allows you to initiate commands, change or monitor the complete set of CX-1010 parameters, and load/save setup values. Features: Pre-programmed control algorithms for Master, Follower , Follower-with-Offset, Inverse and Custom control. Up to eight user defined parameter configuration blocks with on-the-fly digital input reconfiguration. Optional analog card accommodates input signals from line speed, flow, tension, PLC or dancer position sensors. The precision lead and feedback frequency inputs utilize many types of encoder signals including quadrature, open-collector and differential line drivers. Eight programmable digital outputs are provided for drive control and alarm functions. Literature CX-1010 Technical Reference Manual (PDF format, 2,595kb) CX-1010 Technical Reference Manual (Individual Chapters) CX-1010 Installation/Wiring Guide (PDF format, 336kb) Specifications (PDF format, 147kb) Applications CX-1010 CE Declaration of Conformity (PDF format, 88kb) |
|
M-Trim Control
Precise Speed and Ratio Control The M-Trim control provides precision speed control to standalone (Master) or multi-motor (Follower) motion control applications. Using advanced digital feedback techniques, the M-Trim in Master mode can increase speed precision to within 0.01% of set speed when interfaced to AC or DC type drives. When configured as a Follower in multi-motor systems, the M-Trim can provide zero accumulative error using a speed ratio setpoint. Embedded scaling algorithms permit setpoint (set speed) entry and tach monitoring in engineering units specific to your application. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed... no code to write. Operator Interface for Setup & Monitoring. Speed (Master) or Speed Ratio (Follower) Control. Optional Analog Card. The M-Trim control is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Trim control is pre- programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Trim control has a serial port for RS422/485 communication. ContrexHost software, when installed on a Windows PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controls. Features: Pre-programmed control algorithms for Master, Follower and Follower-with-Offset control. Up to four preset Master or Follower setpoints with on-the-fly digital input reconfiguration. Optional analog card accommodates input signals from line speed, flow, tension, PLC or dancer position sensors. The precision lead and feedback frequency inputs utilize either magnetic pick-up or open-collector encoder and proximity sensors. Six programmable digital outputs are provided for drive control and alarm functions. Literature M-Trim Installation/Start-Up Guide (PDF format, 61kb) Specifications (PDF format, 147kb) Applications UL, cUL Listing (PDF format, 262kb) |
|
M-Drive Control
Precise Speed and Ratio Control/Drive The M-Drive provides precision speed control to standalone (Master) or multi-motor (Follower) motion control applications. Using advanced digital feedback techniques, the M-Drive can increase speed precision to within 0.01% of set speed in Master mode applications. When configured as a Follower in multi-motor systems, the M-Drive can provide zero accumulative error using a speed ratio setpoint. Embedded scaling algorithms permit setpoint (set speed) entry and tach monitoring in engineering units specific to your application. Integrated ¼ to 2 HP Single Quadrant DC Drive. Pre-Programmed... no code to write. Operator Interface for Setup & Monitoring. Speed (Master) or Speed Ratio (Follower) Control. Optional Analog I/O Card. The M-Drive is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Drive is pre- programmed, applications can be commissioned in a matter of minutes once the drive has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Drive has a serial port for RS422/485 communication. ContrexHost software, when installed on a Windows PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controls. Features: Pre-programmed control algorithms for Master, Follower and Follower-with-Offset control. Up to four preset Master or Follower setpoints with on-the-fly digital input reconfiguration. Optional analog card accommodates input signals from line speed, flow, tension, PLC or dancer position sensors. The precision lead and feedback frequency inputs utilize either magnetic pick-up or open-collector encoder and proximity sensors. Six programmable digital outputs are provided for drive status and alarm functions. Literature M-Drive Installation/Start-Up Guide (PDF format, 61kb) Specifications (PDF format, 147kb) Applications UL, cUL Listing (PDF format, 213kb) |
|
M-Track Control
Synchronizing Control The M-Track controller is a configurable, microprocessor-based digital controller. The M-Track provides synchronized control in applications requiring one part of a process to follow or be paced by another part of a process. It detects trends such as variations in product spacing or stretch in web applications and automatically compensates to maintain correct synchronization. Typical installations include wicket oven loading, bucket and cartoner synchronization, transfer conveyers, or form/fill/seal pouch packaging. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed.. no code to write. Operator Interface for Setup & Monitoring. Full Registration & Synchronization. Learn Mode for Set-Up. The M-Track control is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Track control is pre-programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Track control has a serial port for RS422/485 communication. ContrexHost software, when loaded on a Windows® PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controllers. Features: Three modes of control (master, follower and computer-supervised) for any AC or DC drive. Eight preset setpoints, five alarms for limit and deviation setpoints, scaling, trending, lock-out and setpoint limit. Learn mode scaling feature automatically calculates the proper scaling ratio between the lead and follower. Reads quadrature encoders to monitor line speed and direction. Literature Specifications (PDF format, 147kb) Applications UL, cUL Listing (PDF format, 262kb) |
|
M-Rotary Control
Rotary Knife/Drum Control The M-Rotary controller is a configurable, microprocessor-based digital controller. The M-Rotary provides control in continuous rotary, cut-to-length or impression print applications. In a lead-follower process, the M-Rotary controls the follower device. It controls the rotary die or web speed in either sync or non-sync mode. Typical installations include web process cutting, perforating, sealing and sheeting of materials. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed.. no code to write. Operator Interface for Setup & Monitoring. Full Registration & Synchronization. Electronic Cam (Match Speed at Impact). The M-Rotary control is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Rotary control is pre-programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Rotary control has a serial port for RS422/485 communication. ContrexHost software, when loaded on a Windows® PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controllers. Features: Synchronized profiling feature functions as an electric cam to match lead speed at contact. Trend feature adjusts for variable print lengths to compensate for correct synchronization. Eight follower setpoints, high sync rate and control bandwidth, lead and follower sync divide, and closed-loop speed/position regulation. Reads quadrature encoders to monitor line speed and direction. Literature Specifications (PDF format, 147kb) Applications UL, cUL Listing (PDF format, 262kb) |
|
M-Cut Control
Cut-to-Length/Index Control The M-Cut controller is a configurable, microprocessor-based digital controller. The M-Cut provides control for incremental feed and cut-to-length applications such as direct point-to-point, registration reference and shuttle carriage operations. Point-to-point applications move from a predefined (home) origin point, through a S-curve velocity profile, directly to a destination point. Registration reference point applications determine the final destination point by the occurrence of a registration mark. Typical installations include sheeters, press feeders, shuttle transfer mechanisms, or one-axis indexers. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed.. no code to write. Operator Interface for Setup & Monitoring. Cut-to-Length or Index Destination. Scaled in convenient Engineering Units. Reacts to Register Marks if they are present. Incremental and Absolute positioning. The M-Cut control is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Cut control is pre-programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Cut control has a serial port for RS422/485 communication. ContrexHost software, when loaded on a Windows® PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controllers. Features: Three in-position outputs with adjustable delay/dwell. Incremental move or absolute position control. Performs combinational entry checking on parameters. Unique programming features include entry for kerf adjustment, back-step length or Home offset. Reads quadrature encoders to monitor line speed and direction. Literature Specifications (PDF format, 147kb) Applications UL, cUL Listing (PDF format, 262kb) |
|
M-Shuttle Control
Flying Cut-Off Control The M-Shuttle controller is a configurable, microprocessor-based digital controller. The M-Shuttle provides control for reciprocating lead/follower motion applications. It's designed specifically for applications of constant motion extruded or web product that cannot be halted for processing (cutting, stamping, threading, etc.). The M-Shuttle moves the process device (saw, grinder, etc.) at the same speed as the product to perform the process at the proper product length. After processing, The M-Shuttle moves the process device back to the original home position and the motion profile is repeated. M-Shuttle applications include flying cutoffs of extruded pipe or sheet types of material. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed.. no code to write. Operator Interface for Setup & Monitoring. Automatic Profile Generation. Batching. Trending. Sync Registration. The M-Shuttle control is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Shuttle control is pre-programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Shuttle control has a serial port for RS422/485 communication. ContrexHost software, when loaded on a Windows® PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controllers. Features: Four preset setpoints (cut lengths), automatic recovery profile generation, trending, sync registration, batching. Three programmed discrete outputs interface to clamping, sawing, grinding or similar devices. Reads quadrature encoders to monitor line speed and direction. Literature M-Shuttle Installation/Start-Up Guide (PDF format, 58kb) Specifications (PDF format, 147kb) Applications UL, cUL Listing (PDF format, 262kb) |
|
M-Traverse Control
Level Wind/Web Scan Control The M-Traverse controller is a configurable, microprocessor-based digital controller. The M-Traverse provides precision digital control for reciprocating "back-and-forth" applications. Perfect for level wind guides in the wire, cable and tubing industries; crosslapping fiber and fabric web; scanning for web inspection or chemical applications; fiber wound tanks and cylinders. Isolated Analog Interface to any AC or DC Drive. Pre-Programmed.. no code to write. Operator Interface for Setup & Monitoring. Automatic Profile Generation. Batch or Layer Counting. Interrupt / Resume Configurations. The M-Traverse control is housed in a ½ DIN vertical instrument enclosure with embedded operator interface. The integrated display and keypad panel gains access to numerous control and monitor parameters. Individual application requirements are met by simply accessing the relevant code parameter and then entering the appropriate numerical value. Because the M-Traverse control is pre-programmed, applications can be commissioned in a matter of minutes once the control has been installed. A full compliment of monitor parameters are available to verify operation and assist with diagnostics. The M-Traverse control has a serial port for RS422/485 communication. ContrexHost software, when loaded on a Windows® PC or laptop, allows you to initiate commands, change parameters, load/save setup values, and monitor more than 50 values on one or up to 32 channels of M-Series controllers. Features: The operator can enter any pitch and width from the keypad directly in engineering units like inches or millimeters. Four preset setpoints (process lengths)can be loaded for selection by switch or PLC contacts. These setpoints can be changed on-the-fly. Reads quadrature encoders to monitor line speed and direction. Literature M-Traverse User Manual (PDF format, 833kb) M-Traverse Installation/Start-Up Guide (PDF format, 63kb) Specifications (PDF format, 147kb) UL, cUL Listing (PDF format, 262kb) |
|
If you can't find what you are looking for
Call Us! or go to the
Contrex Home Page |
|
Seltrol is a stocking distributor of a wide
variety of industrial automation equipment. We are located in South
Carolina and service SC and NC. Our inside and outside sales staff are
available to assist you with your application. We provide technical -
application support for all of our products.
|
|
Contrex Fenner Drive Controls
|