|
Electric Cylinders - Rod Type
The EC2 series is a low cost linear motion package for light to moderate thrust loads ranging up to 3600 N [810lb] and travel up to 600 mm [23.6]. Precision rolled ballscrews are standard, yielding quiet operation, low backlash and high accuracy. EC2 Series electric cylinders are available with brushless servo, step motors, or DC servo for compatibility with every motion control environment. Both ballscrew and acme screw models provide a variety of speed and thrust capabilities. Ballscrew models are used in applications that require higher speed and duty cycles. Acme screw models generally perform best in low duty cycle applications, and where load holding is required without a brake or in the case of electrical power loss. The life expectancy of a ballscrew is generally better than an acme screw. Standard ballscrews are 5 mm and 16 mm lead, and acme screws are available in 4 mm lead. EC2 timing belt or gear reductions between the motor and leadscrew allow selection of the best match between motor power and your linear speed and thrust range. Metric Series Advantages Meets the needs of customers who manufacture forthe international marketplace Both English and Metric versions of threaded mounting options are standard Options Options include rotary encoders or linear potentiometers for position feedback, load-holding brakes, protective boots, and quick-disconnect cables. Industrial Devices will also discuss unique modifications at your request. The EC3 series is a robust linear motion package for moderate to heavy thrust loads ranging up to 7200 N [1620 lb] and travel up to 800 mm [31.5 in]. Precision rolled ballscrews are standard, yielding quiet operation, low backlash and high accuracy. EC3 Series electric cylinders are available with brushless servo, step motors, or DC servo for compatibility with every motion control environment. Both ballscrew and acme screw models provide a variety of speed and thrust capabilities. Ballscrew models are used in applications that require higher speed and duty cycles. Acme screw models generally perform best in low duty cycle applications, and where load holding is required without a brake or in the case of electrical power loss. The life expectancy of a ballscrew is generally better than an acme screw. Standard ballscrews are 5 mm, 10 mm and 16 mm lead, and acme screws are available in 4 mm lead. EC3 timing belt or gear reductions between the motor and leadscrew allow selection of the best match between motor power and your linear speed and thrust range. Options Options include rotary encoders or linear potentiometers for position feedback, load-holding brakes, protective boots, and quick-disconnect cables. Industrial Devices will also discuss unique modifications at your request. The EC4 series is a heavy-duty cylinder, for thrust loads ranging up to 12000 N [2700 lb] and travel up to 1500 mm [59.1 in]. Precision rolled ballscrews are standard, yielding quiet operation, low backlash and high accuracy. EC4 Series electric cylinders are available with brushless servo, step motors, or DC servo for compatibility with every motion control environment. Both ballscrew models provide a variety of speed and thrust capabilities. Ball screw models are used in applications that require high speed and duty cycles. Standard ballscrews are 10 mm and 25 mm lead. EC4 timing belt or gear reductions between the motor and leadscrew allow selection of the best match between motor power and your linear speed and thrust range. Options Options include rotary encoders or linear potentiometers for position feedback, load-holding brakes, protective boots, and quick-disconnect cables. Industrial Devices will also discuss unique modifications at your request. The EC5 series is our highest thrust cylinder, for heavy thrust loads ranging up to 25000 N [5620 lb] and travel up to 1500 mm [59.1 in]. Precision rolled ballscrews are standard, yielding quiet operation, low backlash and high accuracy. EC5 Series electric cylinders are available with brushless servo, step motors, or DC servo for compatibility with every motion control environment. Both ballscrew and acme screw models provide a variety of speed and thrust capabilities. Ball screw models are used in applications that require higher speed and duty cycles. Acme screw models generally perform best in low duty cycle applications, and where load holding is required without a brake or in the case of electrical power loss. The life expectancy of a ballscrew is generally better than an acme screw. Standard ballscrews are 10 mm, 25 mm and 32 mm lead, and acme screws are available in 6 mm lead. EC5 timing belt or gear reductions between the motor and leadscrew allow selection of the best match between motor power and your linear speed and thrustrange. Options Options include rotary encoders or linear potentiometers for position feedback, load-holding brakes, protective boots, and quick-disconnect cables. Industrial Devices will also discuss unique modifications at your request. The N2 and NV Series electric cylinder designs are the result of over 25 years of customer-focused product evolution. Their predecessor, the N Series, was introduced in 1993, an improvement over previously tie-rod style electric cylinders that IDC pioneered in the industry. Tens of thousands of N Series cylinders are currently in the field, making the N Series the most prolific electric cylinder design in the world. N2 Series Today, IDC offers the N2 as the next generation in the N Series family of products. The N2 provides the performance range of the N in a more rugged and higher quality package. N2 Offers Highest Customization More specials and standard product development exists in the N2’s history than any other electric cylinder available today. The N2 is both flexible and robust to accommodate nearly every industrial motion control application. In fact, the N2 offers the most available custom options of all IDC products. Improved Anti-Rotation System A significant N2 improvement lies in the newly designed anti-rotation guide flange, which is eight times as strong as the previous N Series version. The guide flange prevents rotation of the ball nut or acme nut, a requirement for linear motion to occur in all electric cylinder designs. The new design benefits from a combination of die-cast and injection molding technologies, resulting in a ‘bulletproof’ design which virtually immune to failures during installation (tightening fasteners on the rod-end fitting) or accidental hard stops. No Charge for Nonstandard N2 Stroke Lengths Our manufacturing process can quickly respond to custom stroke length requests, which aids you in selecting the length actuator that best fits the application. Custom N2 stroke lengths are normally available in the same lead-time as our standard lengths. NV cylinders are only available in standard stroke lengths. Smaller, More Economical Limit Switches Also updated are the limit switches used to indicate stopping, home or end-of-travel positions on the N2 Series. They are smaller and better environmentally sealed (IP67) than the N Series switches, as well as being less expensive. Same Mounting Footprint as N Series The N2 Series retains the compact design (very low overall length per actuator usable stroke), and is footprint compatible with the N Rodless Actuators The R2A Series is designed as a low cost package for light to moderate loads up to 50 lbs [22.7 kg] and travel up to 72 inches [1830 mm]. It uses low cost, internal, self-lubricating plastic bearings in a lightweight aluminum housing. The same flexible seal used with the R3 and R4 Series prevents environmental contamination and ensures long life, making it an effective, industrial-grade solution. Two basic drive mechanisms can be used: Belt-drive offers the most rapid moves, and leadscrew offers the highest thrust capacity and repeatability. There are four motor types available to meet a variety of application requirements: R2A-D – 24 Volt DC Cost effective. Simple motion. Open loop operation. R2A-H – 160 Volt DC High torque brushed DC servo motor. Precise closed loop operation. Thrust monitored. R2A-S – Step Motor High load and duty cycle. In-position holding. Economical open loop operation (encoder optional). Repeatable positioning to 0.0005 inches [0.013 mm] The R3 series actuators fit the majority of rodless applications where carriage loads are less than 100 lbs [445 N]. A robust design using an internal linear motion guide rail and our built-in flexible seal ensures reliable operation in an industrial environment. Two basic drive mechanisms can be used: Belt-drive offers the most rapid moves, and leadscrew offers the highest thrust capacity and repeatability. There are four motor types available to meet a variety of application requirements: R3-D – 24 Volt DC Cost effective. Simple motion. Open loop operation. R3-H – 160 Volt DC High torque brushed DC servo motor. Precise closed loop operation. Thrust monitored. R3-S/P – Step Motor High load and duty cycle. In-position holding. Economical open loop operation (encoder optional). Repeatable positioning to 0.0005 inches [0.013 mm]. The R4 is our most powerful rodless actuator and can carry the heaviest carriage loads. With its internal linear motion guide bearing, and built-in flexible seal, the R4 Series is designed for operation in an industrial environment. Two basic drive mechanisms can be used: Belt-drive offers the most rapid moves, and leadscrew offers the highest thrust capacity and repeatability. There are three motor types available to meet a variety of application requirements: R4-H – 160 Volt DC High torque brushed DC servo motor. Precise closed loop operation. Thrust monitored. R4-SP – Step Motor High load and duty cycle. In-position holding. Economical open loop operation (encoder optional). Repeatable positioning to 0.0005 inches [0.013 mm]. LM Series Overview The LM Series Linear Modules Provide a Complete Packaged Linear Motor System. The LM series linear modules are fully integrated linear motor stages. The LM series was designed for maximum system performance and ease of application. Thrust and velocity data is guaranteed when used with IDC's line of B8000 series servo products. Very Compact Cross Section Guaranteed Performance Curves for IDC Linear Modules make selecting and applying linear motors in your application a snap! No more calling motor and drive manufacturers to try to determine actual motor performance. LM series modules are ready-to-use linear motor stages with readily accessible Engineering information: force ratings, moment load ratings, deflections vs. moment load, module weights, mounting guidelines, etc. This eliminates the need for customers to design, procure, assemble, and test their own stage design. All linear motor systems are tested at IDC prior to shipment to the customer as part of our quality assurance program. All LM series linear modules are backed by a one-year warranty from IDC Both Optical and Magnetic Encoders are available providing the user with a range of standard resolutions that are readily available (from 0.5 micron to 10 micron standard). Strokes up to 57" possible with the LM25 series Strokes up to 73" possible with the LM38 series LM25 Specifications LM38 Specifications
Cartesian Systems
|
|
If you can't find what you are looking for
Call Us! or go to the
IDC Home Page |
|
IDC Linear Actuator Products
|
|
Seltrol is a stocking distributor of a wide
variety of industrial automation equipment. We are located in South
Carolina and service SC and NC. Our inside and outside sales staff are
available to assist you with your application. We provide technical -
application support for all of our products.
|