Interlinkbt Ethernet Fieldbus Bricks

Seltrol is a stocking distributor of a wide variety of industrial automation equipment. We are located in South Carolina and service SC and NC. Our inside and outside sales staff are available to assist you with your application. We provide technical - application support for all of our products.

Part Number	Description
FENP-S0800	8 Discrete Inputs
FENP-S0008G	8 Discrete Outputs
FENP-S0808G	4x2 Discrete Inputs and 4x2 Discrete Outputs
FENP-S1600	16 Discrete Inputs
FENP-XSG16	16 Inputs or Outputs

Ethernet AIM Stations

Ethernet is rapidly becoming the network of choice for higher level industrial control applications. Ethernet is used primarily to connect PLC's, Computers, Flat panel displays, and other high level components. FEN series ethernet stations provide a convenient way to connect I/O directly to the ethernet network.

FEN stations can be configured or monitored using standard web browser software. Simply type the IP address of the station into the web browser's address box and an interactive website is displayed. This page will allow you to:

- Monitor inputs
- Monitor diagnostic data
- Set outputs
- Upload/Download device configuration

FEN series stations communicate at 10 or 100M baud, half or full duplex. Ethernet cables can be up to 100 meters each.

Ethernet Shielded Cordsets

	Dimensions and Pinouts (PDF)

Ethernet Cables, Extensions, Shielded eurofast® - Cable Type 841, 843 Only

eurofast®

Bare Wire

Pin (Male)

Socket (Female)

Receptacle

84x

RSS

RKS

RJ45S

RSS

RSS 84x-*M

RSS RSS 84x-*M

RKS

RKS 84x-*M

RSS RKS 84x-*M

RKS RKS 84x-*M

FSSD

FSSD 84x-*M

RSS FSSD 84x-*M

RKS FSSD 84x-*M

RJ45S FSSD 84x-*M

FKSD

FKSD 84x-*M

RSS FKSD 84x-*M

RKS FKSD 84x-*M

RJ45S FKSD 84x-*M

RJ45S

RJ45S 84x-*M

RSS RJ45S 84x-*M

»»

RKS RJ45S 84x-*M

»»

RJ45S RJ45S 84x-*M

»»

x - indicates cable type.

* - indicates length in meters.

For stainless steel coupling nut: Change part number (RSS to RSSV...FSFD to FSSDV).

»» - Change part number from RSS RJ45S to RSS RJ45S CR for cross-over cable.

NOTE: If uplink port on Ethernet Switch is used as an active port you must use a crossover cable (i.e. RSS RJ45S CR 841-*M).

Conduit Adapter

	eurofast®
1-port	BCA 84-E124
2-port	BCA 84-E224

Consult factory for stainless steel connectors.

The conduit adapter attaches to a standard conduit body
for transition to minifast® or eurofast® connectors.

Note: Gasket and mounting hardware included (8-32 x 1/2")

CROUSE - HINDS Hub Size = 3/4
Shape	Style	Part Number
	Form 8 Mark 9	C28 C29
	Form 8 Mark 9	LB28 LB29
	Form 8 Mark 9	LL28 LL29
	Form 8 Mark 9	LR28 LR29

Accessory
	Part Number: TOOL, PUNCHDOWN/ETHERNET - Non-impact punchdown tool

Ethernet Cabinet Adapter
	Part Number: BIC 84-E424
The cabinet adapter attaches to a standard cabinet for transition to RJ45 connectors. Gasket and mounting hardware included (8-32 x 1/2").

9-port Ethernet Switch
	Part Number: SE-84X-E924
The high performance Industrial Ethernet Switch provides nine eurofast® ports. The switch complies with the IEEE 802.3 10Base-T Ethernet and 802.3u 100Base-TX Fast Ethernet Standards. The Ethernet Switch can be used in your application to segment network traffic, extend ethernet connection distance, or convert data packets between different transmission speeds. The Switch auto-senses transmission speeds and stores addresses in its routing table. The switch supports store-and-forward switching architecture.

Ethernet Switch
	Part Number: SE-84X-E524
The high performance Industrial Ethernet Switch provides five eurofast® ports. The switch complies with the IEEE 802.3 10Base-T Ethernet and 802.3u 100Base-TX Fast Ethernet Standards. The Ethernet Switch can be used in your application to segment network traffic, extend ethernet connection distance, or convert data packets between different transmission speeds. The Switch auto-senses transmission speeds and stores addresses in its routing table. The switch supports store-and-forward switching architecture.

Ethernet Cables
	Dimensions and Pinouts (PDF)

Ethernet Cable Specifications

Cable that meets the requirement of TIA/EIA568-A category 5e cable for 10 and 100 Base-T ethernet.

Maximum 100M of cable of which:
- 90 M Horizontal Cable (SOLID - 842 or 843)
- 2 x 5 M Patch Cables (STRANDED - 840 or 841)

(OR)

- Direct Connect 30 M stranded

Type	Approvals	AWG	DCR (/1000 ft) Insulation	Material Color Nominal O.D.	Shield Type	Bulk Cable^
840	NEC CMR(ETL) CEC C(ETL)	8/24 Stranded	28.6 PE	PVC Teal 5.9mm (.231)	None	RB50856-*M
841	NEC CMR(ETL) CEC C(ETL)	8/24 Stranded	28.6 PE	PVC Teal 7.3mm (.286)	Foil/Braid	RB50893-*M
842	NEC CMR(ETL) CEC C(ETL)	8/24 Solid	28.6 PE	PVC Teal 5.9mm (.231)	None	RB50857-*M
843	NEC CMR(ETL) CEC C(ETL)	8/24 Solid	28.6 PE	PVC Teal 7.3mm (.286)	Foil/Braid	RB50894-*M

Cable is UL rated for sunlight and oil resistant.
* indicates length in meters.